3M FC3283 electronic fluoride solution CAS 86508-42-1

Introduction
3M™ Novec™ 7200 Engineered Fluid, ethoxy-nonaful orobutane (C4F9OC2H5), is a clear, colorless and low-odor
ful id intended to replace ozone-depleting substances (ODSs), compounds with high global warming potential
(GWP) and chlorinated materials in many applications. Its physical properties are compared with several other
ODS replacement ful id candidates in Tables 1 and 2.
This proprietary ful id has zero ozone depletion potential and other favorable environmental properties (see Table
2). It is low in toxicity, with a time-weighted average exposure guideline of 200 ppm (eight hour average).
Novec 7200 ful id has a higher boiling point than most CFCs, HCFCs and HFCs, reducing evaporative losses.
The low surface tension and low viscosity of Novec 7200 ful id make it ideal for use in vapor degreasing and cold
cleaning applications. In addition, its chemical and thermal stability, nonfal mmability and low toxicity make it
useful for other industrial applications such as specialty solvent and heat transfer applications (see below).

Applications
• Cold cleaner (fel x circuits, wipe solvent)                                              • Lubricant carrier  Fluorocarbons  Hydrocarbons   Silicones
• Cleaning and rinsing agent for vapor degreasing 
• Light-duty cleaning (neat)–particulates,                                                • CFC, HCFC, HFC and PFC replacement agent
ful orolubes, light oils, ful oropolymers                                   
• Specialty solvents, dispersion medium, reaction                                  • Heat Transfer Fluid (See 3M Electronic Materials
medium, extraction solvent                                                                        “Thermal Management Fluids and Services”
• Spray contact cleaner                                                                               brochure.)

Material Description

1 Novec 7200 fluid (C4F9OC2H5) consists of two inseparable isomers with essentially identical properties.
These are (CF3)2CFCF2OC2H5 (CAS No. 163702-06-5) and CF3CF2CF2CF2OC2H5 (CAS No. 163702-05-4).

Typical Physical Properties

Table 1

Environmental and Safety Properties

Table 1

1 CFC-11=1.0
2 GWP–100 year ITH, CO2 = 1.0
Note: HCFC-225 ca/cb ratio is 45/55

Vapor Pressure and Density

The variation of vapor pressure and density with temperature for 3M™ Novec™ 7200 Engineered Fluid can be
calculated using the following formulas:
Vapor Pressure: ln P = 22.289 - 3752.1 [1/(t+273)]
Density: D = 1.4811 - 0.0023026t
P = Vapor Pressure in Pascals
t = Temperature in °C
D = Density in g/ml

Regulatory Status

Novec 7200 ful id has been accepted for commercial use by regulatory agencies in the United States, Europe,
Canada, Japan, Korea and the Philippines (less than 2,000 lbs/yr). The components of Novec 7200 ful id have
been nominated to China’s draft chemical inventory.
Novec 7200 ful id has been approved under the Signifci ant New Alternatives Policy (SNAP) of the U.S. EPA.
Novec 7200 ful id has been excluded by the U.S. EPA from the definition of a VOC on the basis that this
compound has negligible contribution to tropospheric ozone formation. In addition, the South Coast Air
Quality Management District (SCAQMD) has certifei d Novec 7200 ful id as a Clean Air Solvent.
The components of Novec 7200 ful id are not on any regulated lists.
Contact your local 3M representative regarding the regulatory status of Novec 7200 ful id in other countries.

Safety and Handling

Before using this product, please read the current product Material Safety Data Sheet (available through your
3M sales or technical service representative) and the precautionary statement on the product package. Follow
all applicable precautions and directions.
3M™ Novec™ 7200 Engineered Fluid is nonfal mmable and does not exhibit fal mmability characteristics under
normal operating and storage conditions. This ful id is highly resistant to thermal breakdown and hydrolysis in
storage and during use. Recommended handling procedures are provided in the pertinent Material Safety Data
Sheet which is available from your local 3M representative upon request.

1 Exposure Guideline set by the 3M Medical Department

Materials Compatibility

Continuous Exposure

Novec 7200 ful id is compatible with most metals and hard polymers. Soft and elastomeric materials should be
limited to compounds that contain the least amount of extractable plasticizer. 3M technical service engineers
can suggest appropriate compounds and assist with material compatibility tests.

Non-Continuous Exposure

Short-term testing of Novec 7200 ful id demonstrates compatibility, after one hour exposure at boiling
temperature, with a wide range of metals, plastics and elastomers, similar to the performance of perful orinated
liquids. Good short-term compatibility with particularly sensitive plastics such as polycarbonate and PMMA
indicates utility in cleaning of assemblies containing many composite materials.
As with most ful orinated liquids, Novec 7200 ful id will absorb into ful orinated plastics and elastomers over
longer exposures.
 

Short-Term Exposure Compatibility

Exceptions: Some swelling of PTFE and Silicone Rubber. Some surface oxidation of copper during heat aging.

Packaging and Availability

3M™ Novec™ 7200 Engineered Fluid may be ordered in the following container sizes:

• 55-gallon drum; 5-gallon pail;
1-gallon pail

• 4-ounce samples for limited or
preliminary test work are available

Environmental Policy

3M will continue to recognize and exercise its responsibility to prevent pollution at the source wherever and
whenever possible; develop products that will have a minimal effect on the environment; conserve natural
resources through the use of reclamation and other appropriate methods; assure that its facilities and products
meet and sustain the regulations of all federal, state and local environmental agencies; assist, wherever
possible, governmental agencies and other offci ial organizations engaged in environmental activities.

Recycle and Disposal Options

Used Fluid Return Program

3M offers a program for free pickup and return of used 3M specialty ful ids in the U.S. A pre-negotiated
handling agreement between users and our authorized service provider offers users broad protection against
future liability for used 3M product. The ful id return program is covered by independent third-party financial
and environmental audits of treatment, storage and disposal facilities. Necessary documentation is provided.
A minimum of 30 gallons of used 3M specialty ful id is required for participation in this free program.
For additional information on the 3M Used Fluid Return Program, contact your local 3M representative or call
3M Customer Service at 800.810.8513.

Resources

3M™ Novec™ Engineered Fluids are supported by global sales, technical and customer service resources,
with technical service laboratories in the U.S., Europe, Japan, Latin America and Southeast Asia. Users
benefti from 3M’s broad technology base and continuing attention to product development, performance,
safety and environmental issues. For additional technical information on 3M™ Novec™ 7200 Engineered
Fluid in the United States or for the name of a local authorized distributor, call 3M Electronics Markets
Materials Division: 800 810 8513.

3M™ Novec™ Engineered Fluids 3M™ Novec™ Aerosol Cleaners 3M™ Novec™ 1230 Fire Protection Fluid 3M™ Novec™ Electronic Coatings 3M™ Novec™ Electronic Surfactants

United States                               China                                 Europe                                       Japan                                     Korea                          Singapore                           Taiwan

3M Electronics Markets                3M China Ltd.                     3M Belgium N.V.                    Sumitomo 3M Limited             3M Korea Limited        3M Singapore Pte. Ltd.     3M Taiwan Limited 

Materials Division                      86 21 6275 3535                  32 3 250 7521                            813 3709 8250                     82 2 3771 4114              65 64508888                      886 2 2704 9011

800 810 8513

Product Use: All statements, technical information and recommendations contained in this document are based on tests or experience that 3M believes are reliable. However,
many factors beyond 3M’s control can affect the use and performance of a 3M product in a particular application, including conditions under which the product is used and the
time and environmental conditions in which the product is expected to perform. Since these factors are uniquely within the user’s knowledge and control, it is essential that the
user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user’s method of application.

Warranty and Limited Remedy: Unless stated otherwise in 3M’s product literature, packaging inserts or product packaging for individual products, 3M warrants that each 3M
product meets the applicable specifications at the time 3M ships the product. Individual products may have additional or different warranties as stated on product literature,
package inserts or product packages. 3M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. User
is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s application. If the 3M product is defective within the warranty period,
your exclusive remedy and 3M’s and seller’s sole obligation will be, at 3M’s option, to replace the product or refund the purchase price.

Limitation Of Liability: Except where prohibited b.incidental, or consequential regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.
3

Electronics Markets Materials Division
3M Center, Building 224-3N-11                                                            Please recycle. Printed in USA.

St. Paul, MN 55144-1000                                                                     Issued: 9/09 © 3M 2009 

 www.3M.com/novec                                                                             All rights reserved. 7005HB                                                3M and Novec are trademarks of 3M Company.

1-800-810-8513                                                                                     98-0212-2374-2                                                                  Used under license by 3M subsidiaries and affiliates.